S Scania Multi 📌 unpin — ▱ ×
Pin a chassis:
Home Vehicle Parts Information Workshop Diagnostics Search Back Forward Help
V
Workshop manuals › P, G, R and T series/L, P, G, R and S series 24 activities 77 ✱ variants

Document

ID
56
Business key
MEEP
Type
77
Variant filter
1=A&1323=E!1=A&1323=F

Activities 24

ID Heading Component MG Filter
1207 The form applies to the P, G, R and T series false 0
1=A&1323=E
1208 The form applies to the L, P, G, R and S series false 0
1=A&1323=F
1737 Clean the engine externally. This is to prevent dirt from entering the engine or its oil system. false Engine 01
1=A&1323=F&4079=C&142=F!1=A&1323=E&408=PF!1=A&1323=F&408=PF!1=A&1323=E&408=QL!1=A&1323=F&408=QL!1=A&1323=E&408=ZW!1=A&1323=F&408=ZW
344 Check for gas leakage before running-in in the workshop false Fuel system 03
1=A&1323=E&520=C!1=A&1323=F&520=C!1=B&1323=E&520=C!1=B&1323=F&520=C
419 Check that the vehicle is not leaking fuel before running-in in the workshop. false Fuel system 03
1=A&1323=E&520=B!1=A&1323=F&520=B!1=B&1323=F&520=B
1660 Make sure that the starter key/starter button is in drive mode and that the function is deactivated via the switch for idle stop and start. false Idle stop and start function 16
1=A&1323=E&5526=A!1=A&1323=F&5526=A!1=B&1323=E&5526=A!1=B&1323=F&5526=A
1654 Carry out Procedures for all workshop operations on electric vehicles before starting work. Information about these procedures can be found in the instructions. false Electric vehicle 00
1=A&1323=F&4034=C!1=B&1323=F&4034=C
1658 Carry out Procedures for all workshop operations on hybrid vehicles before starting work. Information about these procedures can be found in the instructions. false Hybrid vehicles 00
1=A&1323=E&4034=B!1=A&1323=F&4034=B!1=B&1323=E&4034=B!1=B&1323=F&4034=B
394 (no heading) false — —
20 Read any fault codes. Delete the fault codes. false Control units 16
1=A&1323=E!1=A&1323=F!1=B&1323=F
98 Check the oil level. Check for leakage. Fill with oil if necessary. false Engine 01
1=A&1323=E&520=A!1=A&1323=F&520=A!1=A&1323=E&520=B!1=A&1323=F&520=B!1=A&1323=E&520=C!1=A&1323=F&520=C!1=B&1323=F&520=A!1=B&1323=F&520=B!1=B&1323=F&520=C
321 Renew the fuel filter and bleed the fuel system. Renew O-rings at the overflow valve on the fuel filter housing and clean the fuel strainer. false Scania HPI fuel system 03
1=A&1323=E&1470=C
65 Adjust the preload on the unit injectors. false Engine with Scania HPI 01
1=A&1323=E&1470=C
1725 Check and adjust valve clearance. Intake valve: 0.45 mm and exhaust valve: 0.70 mm. false Diesel engine 01
1=A&1323=E&142=B&520=A&~4079=C!1=B&1323=E&142=B&520=A&~4079=C!1=A&1323=F&142=B&520=A&~4079=C!1=A&1323=E&142=D&520=A!1=B&1323=F&142=B&520=A&~4079=C!1=B&1323=E&142=D&520=A!1=A&1323=F&142=D&520=A!1=A&1323=E&142=E&520=A!1=B&1323=F&142=D&520=A!1=B&1323=E&142=E&520=A!1=A&1323=F&142=E&520=A!1=A&1323=E&142=F&520=A!1=B&1323=F&142=E&520=A!1=B&1323=E&142=F&520=A!1=A&1323=F&142=F&520=A!1=A&1323=E&142=H&520=A&~4079=C!1=B&1323=F&142=F&520=A!1=B&1323=E&142=H&520=A&~4079=C!1=A&1323=F&142=H&520=A&~4079=C!1=B&1323=F&142=H&520=A&~4079=C
1228 Check and adjust valve clearance. Intake valve: 0.25 mm and exhaust valve: 0.5 mm. false Diesel engine DC07 01
1=A&1323=F&142=K!1=B&1323=F&142=K
423 Check and adjust valve clearance and unit injectors. Intake valve: 0.45 mm and exhaust valve: 0.70 mm. false Ethanol engine 01
1=A&1323=E&520=B
1016 Check and adjust valve clearance. Intake valve: 0.45 mm and exhaust valve: 0.80 mm. false Gas engine 01
1=A&1323=E&520=C!1=A&1323=F&520=C!1=B&1323=F&520=C
64 Check spring heights of unit injectors and adjust if required. false Engine with PDE 01
1=A&1323=E&520=A&1470=B!1=A&1323=F&520=A&1470=B!1=B&1323=F&520=A&1470=B
1745 For vehicles with propulsion batteries. Use coolant with a freezing point of -38°C or lower. This corresponds to a minimum of 50% addition of coolant concentrate with corrosion protection in the coolant. false 0
1=A&1323=E&4034=B!1=B&1323=E&4034=B!1=A&1323=F&4034=B!1=B&1323=F&4034=B!1=A&1323=F&4034=C!1=B&1323=F&4034=C
1691 For vehicles with LNG fuel: Use coolant with a freezing point of -38°C or lower. This corresponds to a minimum of 50% addition of coolant concentrate with corrosion protection in the coolant. false 0
1=A&1323=E&5841=B!1=A&1323=F&5841=B!1=B&1323=E&5841=B!1=B&1323=F&5841=B
92 Check the fluid level. false Cooling system 02
1=A&1323=E&520=A!1=A&1323=F&520=A!1=A&1323=E&520=B!1=A&1323=F&520=B!1=A&1323=E&520=C!1=A&1323=F&520=C!1=B&1323=F&520=A!1=B&1323=F&520=B!1=B&1323=F&520=C
96 Read any fault codes. Delete the fault codes. false Control units 16
1=A&1323=E!1=A&1323=F!1=B&1323=F
1655 Carry out Procedures for all workshop operations on electric vehicles after the work has been completed. Information about these procedures can be found in the instructions. false Electric vehicle 00
1=A&1323=F&4034=C!1=B&1323=F&4034=C
1657 Carry out Procedures for all workshop operations on hybrid vehicles after the work has been completed. Information about these procedures can be found in the instructions. false Hybrid vehicles 00
1=A&1323=E&4034=B!1=A&1323=F&4034=B!1=B&1323=E&4034=B!1=B&1323=F&4034=B
Change history (sv-SE) 
2023-12-07: Ny admonition om kylvÀtskekoncentrationen för fordon med framdrivningsbatterier. [bib]
2023-10-12: Ny punkt med anledning av rutin med renhet för motorer med blyfria lager. AnvÀnds bara i R för att utesluta CBE1-motorerna. [bib]
2023-10-06: Lagt till admonition med info om kylvÀtskemix för LNG-fordon. [bib]
2023-01-03: Gjort en unik punkt om kontroll av ventilspel till R-underhÄll för att inte fÄ trÀff pÄ CBE1-motorer, dvs. 13-litersmotorer med cylinderblocksgeneration 3. [bib]
2023-01-03: Tagit bort om ventiljustering för motor utrustad med dekompressionsbroms (CRB). CBE1-motorer behöver inte utföra kontroll av ventilerna vid R-underhÄll. [bib]
2021-07-09: Lagt till om ventiljustering och utrustad med dekompressionsbroms (CRB). [bib]
2019-09-05: Lagt till admonitions för stopp-start, rutiner vid arbete med hybrid och stÀnga av gastillförseln.
2017-08-30: Lagt till ventiljustering för DC07 (steg 2) [bib]
2016-07-12: Generationsbeteckning dÀr protokollpunkterna börjar. I och med att vi har gemensamma protokoll för PGRT och PGRS (NCG) behöver vi ange bÄda under protokollhuvudet. [bib]
2015-10-13: Uppdaterat villkorssÀttningen för NCG. [bib]
2013-10-15: Vi fÄr göra 2 separata protokoll eftersom fÀltet Fordonstyp mÄste vara ifylld för att protokollet ska synas i Multi.
workshop