DTC ›
MCC3
| Code | Heading | Variants |
|---|---|---|
| 0046 | — | — |
| 0047 | — | — |
| 0048 | — | — |
| 0049 | — | — |
| 004A | — | — |
| 004B | — | — |
| 004C | — | — |
| 004D | — | — |
| 004E | — | — |
| 004F | — | — |
| 005A | — | — |
| 005B | — | — |
| 005C | — | — |
| 005D | — | — |
| 005E | — | — |
| 005F | — | — |
| 0060 | — | — |
| 9999 | This DTC is set if an INTE (Internal Event) code has been registered. | — |
| A00A | Evaporator temperature sensor (T81), short circuit to battery, open load, or sensor is broken. | — |
| A011 | The cab fan (M3) supply voltage is out of range (below 16V or above 32V). | — |
| A012 | The cab fan (M3) is overheated. | — |
| A013 | The cab fan (M3) is mechanically blocked and cannot rotate. | — |
| A014 | There is an error with the digital feedback signal from the cab fan (M3). | — |
| A015 | The control signal to the cab fan (M3) is short circuit to battery. | — |
| A017 | Actuator mix air (M56) LIN error. | — |
| A018 | Actuator defrost (M59) LIN error. | — |
| A019 | Actuator panel/floor (M57) LIN error. | — |
| A01A | Actuator floor LIN error. | — |
| A01B | Actuator recirc/fresh (M58) LIN error. | — |
| A020 | LIN error on all components. | — |
| A022 | The control signal to the cab fan (M3) is short circuit to ground. | — |
| A023 | The U30 12V supply to the climate control system (E17) is below 8V. | — |
| A024 | The U30 12V supply to the climate control system (E17) is above 16V. | — |
| A027 | There is an internal electrical error with a safety related feature in the climate control system (E17). | — |
| A028 | There is an internal electrical error with the climate control system (E17) shutdown mechanism. | — |
| A029 | 12V supply to LIN nodes (C8063) is short circuit to battery or open load. | — |
| A02A | 12V supply to LIN nodes (C8063) is short circuit to ground. | — |
| A02B | Each knob in the MCC(E17) has a two channel potentiometer. This faultcode indicates that one of the channels has get stuck. | — |
| A02C | Each knob in the MCC (E17) has a two channel potentiometer. This faultcode indicates that one of the channels has get stuck. | — |
| A02D | The calibration for the temperature and fan encoders (knobs) in the MCC (E17) is not valid, | — |
| A030 | Supply error on mix air/temp flap motor (M56). | — |
| A031 | Supply error on air dist/defrost motor(M59). | — |
| A032 | Supply error on panel/floor flap motor (M57). | — |
| A033 | Supply error on floor flap motor | — |
| A034 | Supply error on air intake/recirc control motor (M58). | — |
| A036 | Over temp reported by the mix air/temp flap motor (M56). | — |
| A037 | Over temp reported by the air dist/defrost motor (M59). | — |
| A038 | Over temp reported by actuator for panel/floor (M57). | — |
| A039 | Over temp reported by the floor flap motor. | — |
| A03A | Over temp reported by actuator for recirc (M58). | — |