DTC ›
C300
| Code | Heading | Variants |
|---|---|---|
| 0101 | The SIM card is not detected. | 5× |
| 0103 | The SW cannot detect the GSM antenna. | 5× |
| 0201 | The SW cannot detect the GPS antenna. | 5× |
| 0202 | The GPS antenna takes too much current or is short circuited. | 5× |
| 0203 | GPS not reporting location | — |
| 0301 | No CAN data is received from the vehicle internal CAN bus (CAN1). | 5× |
| 0302 | No CAN data is received from the EMS | 5× |
| 0303 | No CAN data is received from the BMS | 5× |
| 0304 | No CAN data is received from the ICL | 5× |
| 0305 | No CAN data is received from the alarm system | 5× |
| 0306 | No CAN data is received from the COO | 5× |
| 0307 | No CAN data is received from the DTCO | 5× |
| 0308 | No CAN data is received from the DCS | 5× |
| 0309 | No CAN data is received from the BCI | 5× |
| 030A | No CAN data is received from the VIS | 5× |
| 030B | No CAN data is received from the BCS | 5× |
| 0321 | Heater timeout, not responding | 5× |
| 035D | Secondary wake-up bus is short circuit to battery | — |
| 03F0 | It is no possible to send messages on internal CAN bus | 2× |
| 03F1 | It is no possible to send messages on blue CAN bus | 2× |
| 03F2 | It is no possible to send messages on the third CAN bus CAN3 | 2× |
| 0401 | The supply voltage for the communication node is too high. | 5× |
| 0402 | The communication node will shut down at supply voltage 8V and the measure tolerance +/- 0.5V. A DTC has to be created by the unit before the supply voltage gets lower than the critical level for shut down. | 5× |
| 0501 | There is a short circuit to ground on the output to the Digital TCO Wireless File Transfer status LED. | 5× |
| 0502 | There is a short circuit to supply on the output to the Digital TCO Wireless File Transfer status LED. | 5× |
| 0503 | There is a short circuit to ground on the output to the Driver Identity Button status LED. | 5× |
| 0504 | There is a short circuit to supply on the output to the Driver Identity Button status LED. | 5× |
| 0505 | There is a short circuit to ground on the 2:nd wake-up when C300 is waking up other units (active). | 5× |
| 0601 | There is no valid map data available in the RTC ECU. | 5× |
| 0602 | USB connection consumes current above given threshold. | 5× |
| 0603 | CCAP start up failure and the DTC become active. | 5× |
| 0604 | Running system after software rollback due to failed attempt to verify newly applied software | 5× |
| 0605 | Running system after software rollback due to failed attempt to apply new software | 5× |
| 0606 | No software update has been performed or no valid software found | 5× |
| 0607 | Software update has been initiated but not finished | 5× |
| 0608 | Failed software update due to internal platform error | 5× |
| 0609 | Unrecognized USB device connected | 5× |
| 0801 | Internal Backup battery (BuB) is empty or damage | 5× |
| 0901 | Missing driver ID on blue CAN bus | 2× |
| 0902 | Product id registration mismatch | 2× |