DTC ›
COO9
| Code | Heading | Variants |
|---|---|---|
| 0296 | Consistency check error on node not participating in consistency check function. | — |
| 029F | Absence of Red bus communication (CAN1 buffer overflow) | — |
| 02A0 | Absence of Yellow bus communication (CAN2 buffer overflow) | — |
| 02A2 | Key inserted switch plausibly faulty. | — |
| 02A4 | Immo transponder key harness fault. | — |
| 02A5 | Immo transponder key communication fault. | — |
| 02A6 | Immo transponder key, validation fault | — |
| 02A8 | EMS immobilizer validation fault. | — |
| 02A9 | AC pressure sensor open circuit, or short circuit to ground. | — |
| 02AB | AC pressure sensor short circuit to battery | — |
| 02AC | Inputs from comfort shift lever do not agree | — |
| 02AE | ACS node inconsistent configuration | — |
| 02B0 | AC pressure is too high | — |
| 02B1 | AC pressure is too low | — |
| 02B3 | ACS node: Time-out in CAN communication. | — |
| 02B4 | EMS immo: CAN timeout in communication with EMS immo unit. | — |
| 02B7 | XBR system state error. BMS configuration fault. | — |
| 02BD | Engine vehicle speed control state error. EMS configuration fault. | — |
| 02BE | GMS auxiliary brake manager vehicle speed control state error. GMS configuration fault. | — |
| 02C1 | Loss of function parameters | — |
| 02C2 | Loss of KWP2000-ECU ID data | — |
| 02C3 | Loss of persistent IMMO data | — |
| 02C4 | Loss of SOPS data | — |
| 02CF | Propeller shaft speed sensor signal does not agree with signal from ABS-sensors. | — |
| 02D0 | Vehicle blocking is requested. | — |
| 02DD | RTC node: timeout in CAN communication. | — |
| 02DF | Scania Gear Selector plausable fault | — |
| 02E0 | BCI node inconsistent configuration | — |
| 02E1 | BCI node: timeout in CAN communication. | — |
| 02E3 | RTC node wrong ADASIS protocol version | — |
| 02E5 | LIN RCU1 (Remote Control Unit 1) node: timeout in LIN communication | — |
| 02E6 | LIN RCU2 (Remote Control Unit 2) node: timeout in LIN communication | — |
| 0306 | Plausibility test for LDW enable/disable switch has failed. | — |
| 0307 | Plausibility test for AEB enable/disable switch has failed. | — |
| 0309 | Electrical error on the environment sensor CAN bus (CAN4 BusOff) | — |
| 031A | Communication error on the LIN bus | — |
| 031E | ISAS button error | — |
| 0320 | Comfort shift interlock short circuit to ground | — |
| 0321 | Comfort shift interlock open load or short to battery | — |
| 0324 | 61 relay short circuit to ground | — |
| 0325 | 61 relay open load or short circuit to battery | — |
| 0326 | Timeout in CAN communication from Steering Angle Sensor (SAS) node | — |
| 0327 | Steering Angle Sensor (SAS) is NOT calibrated | — |
| 0328 | Faulty Steering Angle Sensor (SAS) unit | — |
| 0329 | Outputs are disabled when they should be enabled. | — |
| 032A | All outputs are enabled when they should be disabled. | — |
| 032B | Power hold functionality is disabled when it should be enabled. | — |
| 032C | Implausible diff knob position | — |
| 032E | Electrical error on orange CAN bus (CAN5 BusOff) | — |
| 032F | Electrical error on switch CAN bus (CAN6 BusOff) | — |