DTC ›
DAS2
| Code | Heading | Variants |
|---|---|---|
| 0236 | ICL node: timeout in CAN communication. | — |
| 023B | CUV node: timeout in CAN communication | — |
| 0251 | EBS node: timeout in CAN communication. | — |
| 0253 | BMS mode inconsistent configuration. TO BE REMOVED - ONLY FOR AEB | — |
| 0255 | Electrical error on CAN-bus 1 (CAN1 BusOff). | — |
| 0256 | Electrical error on CAN-bus 2 (CAN2 BusOff). | — |
| 0257 | Electrical error on CAN-bus 3 (CAN3 BusOff) | — |
| 028E | ECU hardware memory failure in program- or calibration flash, internal RAM, external RAM, EEPROM | — |
| 0290 | Inconsistent long term RAM data. | — |
| 0291 | Illegal software operation. | — |
| 0292 | Overloaded software resources. | — |
| 0296 | Consistency check error on node not participating in consistency check function. | — |
| 029F | Absence of Sensor CAN-bus communication (DAS2 CAN1 buffer overflow). | — |
| 02A0 | Absence of CAN2 communication (CAN2 buffer overflow) | — |
| 02B7 | XBR system state error. BMS configuration fault. TO BE REMOVED, ONLY AFFECTS AEB and AICC | — |
| 02C1 | Loss of function parameters | — |
| 02C2 | Loss of KWP2000-ECU ID data. | — |
| 02C3 | Loss of persistent IMMO data | — |
| 02C4 | Loss of SOPS data. | — |
| 02C5 | Loss of operation data. | — |
| 02DD | RTC node: timeout in CAN communication. | — |
| 02E3 | RTC node inconsistent configuration | — |
| 0306 | Plausibility test for LDW enable/disable switch has failed. TO BE REMOVED, LDW NO LONGER I DAS2 | — |
| 0307 | Plausibility test for AEB enable/disable switch has failed. TO BE REMOVED, AEB no longer in DAS2 | — |
| 0308 | DIS2 node inconsistent configuration. | — |
| 0309 | Electrical error on CAN-bus 4 (CAN4 BusOff) | — |
| 030A | DIS2 node: timeout in CAN communication. | — |
| 030B | Timeout in CAN communication with Forward looking camera (FLC) | — |
| 030D | Node inconsistent configuration Forward Looking Camera (FLC). | — |
| 031C | Camera (FLC1) and radar (DIS2) are misaligned. | — |
| 0326 | Timeout in CAN communication from Steering Angle Sensor (SAS) node | — |
| 0327 | Steering Angle Sensor (SAS) is NOT calibrated | — |
| 0328 | Faulty Steering Angle Sensor (SAS) unit | — |
| 0329 | Outputs are disabled when they should be enabled. | — |
| 032A | All outputs are enabled when they should be disabled. | — |
| 032B | Power hold functionality is disabled when it should be enabled. | — |
| 032E | Electrical error on CAN bus 5 (CAN5 BusOff) | — |
| 032F | Electrical error on CAN-bus 6 (CAN6 BusOff) | — |
| 034D | Absence of bus communication (CAN5 buffer overflow) | — |
| 034E | Absence of Spare bus communication (CAN6 buffer overflow) | — |
| 035C | Secondary wake-up bus is short circuit to ground. TO BE REMOVED | — |
| 035D | Secondary wake-up bus is short ciruit to battery. TO BE REMOVED | — |
| 0360 | Sub wake-up bus short circuit to ground. | — |
| 0363 | Distance sensor (DIS) sends essential signals with poor status. | — |
| 0364 | Forward Looking Camera (FLC) sends invalid values. | — |
| 0366 | Electrical Error on CAN bus 1 (Sensor bus) | — |
| 0367 | Electrical Error on canbus 2 | — |
| 0368 | Electrical Error on canbus 3 | — |
| 0369 | Electrical Error on canbus 4 | — |
| 036A | Electrical Error on canbus 5 | — |
page 1 of 6
next →