DTC ›
ACS5
| Code | Heading | Variants |
|---|---|---|
| 0001 | ECU is not correctly EOL programmed (NOT_CONFIGURED_ECU) | — |
| 0002 | Inconsistent pin coding (PIN_CODING_INCONSISTENT) | — |
| 0003 | Node 1 missing (NODE_1_MISSING) | — |
| 0004 | Node 2 missing (NODE_2_MISSING) | — |
| 0005 | Red CAN is missing (CAN_RED_MISSING) | — |
| 0006 | The other node is missing on the red CAN bus (OTHER_NODE_MISSING_ON_RED) | — |
| 0007 | Rose CAN is missing (CAN_ROSE_MISSING) | — |
| 0008 | Implausible signals between angle sensor and end position switch (IMPLAUSIBLE_SENSOR_SIGNALS) | — |
| 0009 | The angle sensor is out of range (ARTICULATION_ANGLE_SENSOR_ERROR) | — |
| 000A | The end position switch is faulty (END_POSITION_SWITCH_ERROR) | — |
| 000B | Continuous signal from the Override Reverse Protection Switch. (OVERRIDE_SWITCH_ERROR) | — |
| 000C | The right pressure sensor is faulty (PRESSURE_SENSOR_RIGHT_ERROR) | — |
| 000D | The left pressure sensor is faulty (PRESSURE_SENSOR_LEFT_ERROR) | — |
| 000E | The right proportional valve is faulty (PROP_VALVE_RIGHT_ERROR) | — |
| 000F | The left proportional valve is faulty (PROP_VALVE_LEFT_ERROR) | — |
| 0010 | The right cylinder is faulty (CYLINDER_RIGHT_ERROR) | — |
| 0011 | The left cylinder is faulty (CYLINDER_LEFT_ERROR) | — |
| 0012 | The BMS is missing. (BMS_MISSING) | — |
| 0013 | The EMS is missing. (EMS_MISSING) | — |
| 0014 | The GMS is missing. (GMS_MISSING) | — |
| 0015 | The TCO is missing. (TCO_MISSING) | — |
| 0016 | The COO is missing. (COO_MISSING) | — |
| 0017 | The reference voltage is faulty (REFERENCE_VOLTAGE_ERROR) | — |
| 0018 | The BCS is missing. (BCS_MISSING) | — |
| 0019 | Inconsistent ignition relay information (IGNITION_RELAY_ERROR) | — |
| 001A | EOL programming in the nodes inconsistent (PARAMETERS_INCONSISTENT) | — |
| 001B | Gateway PinCoding Inconsistent (GATEWAY_PINCODING_INCONSISTENT) | — |
| 001C | Inconsistent ignition relay information, node 2. (IGNITION_RELAY_NODE_2_ERROR) | — |
| 001E | Propvalve right Shortcircuit (PROP_VALVE_NODE_1_SC) | — |
| 001F | Propvalve left Shortcircuit (PROP_VALVE_NODE_2_SC) | — |
| 0020 | Propvalve right Open circuit (PROP_VALVE_NODE_1_OC ) | — |
| 0021 | Propvalve left Open circuit (PROP_VALVE_NODE_2_OC) | — |
| 0022 | Node 1 not flash programmed. (NODE_1_NOT_FLASH_PROGRAMMED) | — |
| 0023 | Node 2 not flash programmed. (NODE_2_NOT_FLASH_PROGRAMMED) | — |
| 0024 | The BWE is missing. (BWE_MISSING) | — |
| 0025 | The end position switch is faulty (END_POSITION_SENSOR1) | — |
| 0026 | The end position switch is faulty (END_POSITION_SENSOR2) | — |
| 1 | — | — |
| 12 | — | — |
| 13 | — | — |
| 14 | — | — |
| 15 | — | — |
| 16 | — | — |
| 17 | — | — |
| 18 | — | — |
| 19 | — | — |
| 1A | — | — |
| 2 | — | — |
| 3 | — | — |
| 4 | — | — |
page 1 of 2
next →